The efficient future for the glass industry is ‘all-electric’

The burning of fossil fuel as an energy source in the glass melting process results in unavoidable carbon emissions and improvements to traditional technology have reached their efficiency limits. Originally published in the September/October issue, René Meuleman says moving to electrical heating methods has many benefits, including improved energy efficiency, more flexible control and less combustion related emissions. The aim of this presentation, delivered at the 14th International Seminar on Furnace Design in Vsetin, Czech Republic, is to stimulate glass manufacturers into re-thinking their existing melting technology and considering ‘all-electric’ melting in the near future.


Glass melting has been carried out for nearly 6000 years and for most of that time, wood was used as the energy source. It was only comparatively recently in around 1880 that the industry began to use fossil fuels like oil and natural gas. At this time, the regenerator had already been invented to improve the efficiency of steel blast furnaces and this was soon adapted by the glass industry on early side port furnaces.

During those thousands of years of glass making, less than 150 years’ worth of fossil fuels were used but it is possible that they will not be around for another 150 years. Although new fossil fuel resources have recently become available, the world has at last begun to understand that burning them results in unavoidable carbon emissions and therefore, this method must come to an end.

Glass melting still needs to continue at this time because no viable replacement material has been discovered. It is likely, therefore, that glass will be around for many centuries to come and that the inevitable future for a carbon efficient glass industry will be ‘all-electric’.

With no disrespect to past furnace design developments and the great achievements that have been made, they are mostly still based on original technology. Traditional side and end port furnaces are proven technology that has been developed and tweaked to a level of efficiency, low emissions and life time that simply cannot be improved any further.

Since the efficiency level came down to 2.4 MWh/ton in around 1990, no major improvements have been achieved. Consequently, further CO 2 and NOx emission reductions slowed to halt as well. Oxy-fuel firing, batch preheating, waste heat recovery, submerged burners etc are great advances but the bottom line remains the same: They all increase the complexity of the melting system and CAPEX, do not avoid CO 2 emissions and in most cases, cannot reduce NOx emissions any further. The use of fossil fuels has become the fundamental problem and
technology cannot overcome these issues sufficiently.

Just like many other raw materials, as soon as mankind starts believing that resources are coming to an end, new ones are found. That is also applicable for fossil fuels. So why should industry even start considering diverting from fossil fuels?

Science has proved that CO 2 emissions are related to global warming, which will likely lead to serious environmental issues for humanity. Legislation, customers and common sense will force the industry to step away from fossil fuel firing sooner or later. By 2050, the EU aims to cut greenhouse gas emissions to 80% below 1990 levels. Milestones to achieve this are 40% emissions cuts by 2030 and 60% by 2040. All sectors need to contribute.

One famous Dutch beer brewer (1) is putting a lot effort into reducing its carbon footprint and estimates that 53% of this is related to its packaging material. The pressure to reduce emissions comes from many sides. No matter which side the industry agrees or disagrees with, it will impact how glass is melted in the future.

Most glass melting furnace technology goes back 100 years or more. Over the years, different developments have led to huge energy efficiency and emission improvements and many furnace suppliers are still working on enhancements, forced by the fact that fossil fuel energy remains cheap. That will change, however and assumingly much faster than many expect.

As previously mentioned, most of those improvements implicate a more complex technology that results in additional maintenance and CAPEX, the use of non-environmentally- friendly chemicals and limitations to equipment lifespan. Most glass melters perceive their melting process as complex enough and are not keen on modifying it further. They want to focus on their core business, without the issues of managing and maintaining complex industrial installations, requiring high numbers of technical personnel.

Keeping the system simple has been a key argument for many decades. Now that the world seems to be changing rapidly, the industry’s efforts to elongate the life time of furnaces up to +15 years is working against it. In fact, most glass manufactures only have one opportunity every 10 to 15 years to introduce an innovative melting process, so it is unsurprising that having to live with that decision for the next 15 years makes them extremely risk-averse. Who can blame them?

It is reminiscent of a comment made by a customer: “In God we trust but here, you have to come with facts.” Technological research and development needs to provide evidence of improvements, otherwise politics forces people to rely on expectations.

Electrically-heated furnace technology is almost as old as regenerative furnace technology. In fact, the first furnace patent on electrical melting was issued to Sauvageon in France, in 1907.

A first successful cold top furnace ran in Norway from 1920 to 1925 using carbon electrodes and Cornelius in Sweden had operating furnaces as early as 1925, producing amber and green glass. In 1952 the industry started to use molybdenum electrodes (2) and in around 1975, high current SCRs (thyristors) became available, leading to the principle of solid-state furnace boosting systems known today. Most modern traditional container, fibre and float furnaces are now equipped with electrical furnace boosting, contributing 10% to 50% of the melting power.

Even in the early days, all-electric melting efficiency at 4.4GJ/ton (3) (1.3MWh/ton) was already close to today’s most efficient fossil fuel fired furnaces at 4GJ/ton (1.1MWh/ton). Since the introduction of all-electric furnaces, huge efficiency improvements have been achieved, reducing energy usage levels to 2.8GJ/ton (0.78MWh/ton) (20% cullet) or less (4) . The power consumption is not likely to go below 2.6GJ/ton (0.72MWh/ton). Most of the electrical power ends up in the melting process anyway and only relatively low energy losses come from transformers, busbar and control efficiency. Compared to traditional fossil fuel heating at 4GJ/ton (1.1MWh/ton), energy use is about 35% less.

An electrical furnace is naturally easy to control and maintain but it is important to consider the engineering of the electrical system alongside the furnace design. Like a burner system for a traditional furnace, the electrical system is not a sub-system but should be part of the total design and needs to be fully integrated. Bringing steelwork, refractory, cables, busbars, electrodes, transformers and control together in one design is essential for the efficiency success of the whole system.

Compared to high efficiency fossil fuel-fired melter systems, all-electric furnaces are sophisticated but very straightforward in terms of design. Regenerators or burner skids are not required and expensive high temperature crowns are not necessary. Higher pull rates can be achieved without any problems. No combustion-related CO 2 , thermal NOx or SOx emissions are released. Potentially, less evaporation of volatile and expensive raw materials, like boron and lithium etc will occur, which makes exhaust filtering much easier. Also, the carryover problem will almost vanish. Smaller furnaces could be considered, e.g. one furnace that feeds one forehearth, which feeds one IS machine, might become a new concept for bottle manufacturing.

Although all-electric furnace concepts are very simple in principle, there are some implications to consider when changing over to this technology. At room temperature, glass or glass compositions are electrical insulators. In order to start the electrical heating process, it needs to run through a preheating sequence similar to the method used in container and float furnaces.

An all-electric furnace also needs a stable, reliable power grid and due to different melting and fining behaviours, the glass composition needs to be changed. Electrical tariffs need to come down in price and in order to lower the carbon footprint, electricity would need to come from renewables instead of coal-fired power plants. Electrodes need to be maintained by advancing them in case wear leads to higher resistance.

There are new methods to counter electrode wear, which would need to be investigated further. Another issue, especially for the container industry, might be how this kind of furnace would handle extremely high amounts of cullet, which may result in different ways cullet and batch are managed.

Electrical power tariffs are strongly related to availability and the electrical energy market is changing rapidly. Suppliers and utilities subsidised by government grants are investing in wind, bio-mass and solar power generation. Citizens also invest in solar panels instead of keeping their money at zero interest in banks. Buzz words such as ‘smart grid’, ‘tariff tweaking’, ‘peak shaving’ and ‘frequency control’ have become familiar terms and it is recognised that money can be saved if the electrical energy consuming system becomes more flexible. In order to lower the risk of total grid failure, some utilities offer money to be in control of huge industrial loads, to be able to temporarily switch them off when needed. More refined is the method of controlling the network’s frequency (Dynamic Fractional Frequency Reuse) by tweaking the power consumption of some massive power consumers.

Basically, electrical power consumers are financially rewarded if they make part of their electrical power consuming system available for remote power control. Lower peak power demand can lead to lower tariffs. In this case, a dynamic load management system, capable of controlling parts of the electrical system to ensure that agreed peak power levels are not exceeded, will lower the overall cost of electrical energy.

A glass furnace, containing a huge amount of molten glass can or should be able to accommodate the flexibility needed to profit from these rewards, grants and lower electrical tariffs. Glass manufacture, being part of the high energy consumer community and rapidly changing energy market, needs to look for furnace designs that better fit both today’s and tomorrow’s requirements. Sophisticated data analysis and (model-based) control strategies should help operators to calculate the available freedom of control, allowable melting energy fluctuations, allowable fossil to electric ratio fluctuations and predict the impact on glass quality.

The bottom line is that there is no escape from thinking ‘out of the box’ and stepping away from tradition.

As a supplier of process and electrical power supply control systems in this business for over 50 years, Eurotherm considers itself to have a strong understanding of the glass industry’s requirements and concerns. For several years now, the company has been promoting the efficiency, financial and environmental benefits of moving to electric heating and has recently witnessed high levels of interest and growth in its SCR-controlled power supply systems.

The move to all-electric will not occur overnight, although the industry is beginning to listen and accept the implications of not starting. Eurotherm will stick to its intuition that the efficient future for the glass industry will be all-electric and is thinking ahead about what needs to be done to achieve that conceptual change eventually. Glassmakers are invited to involve Eurotherm in their internal discussions on electrical heating power supplies and control systems with other enablers and innovators to make this happen. There is no escape and remember, all-electric has been around for +100 years already!

1. Jan Kempers, Heineken, ‘On our way to the greenest bottle’.
2. ‘Handbook of Glass Manufacture’, 1960.
3. NCNG: Textbook, 2012 Glass Technology Course.
4. Hubert de La Forest Divonne and Andy Reynolds, Fives UK.

René Meuleman is Business Leader Global Glass at Eurotherm by Schneider Electric


Eurotherm Ltd, Worthing, West Sussex, UK
tel: +44 1903 268500
email: This email address is being protected from spambots. You need JavaScript enabled to view it.

Latest Video

Hollow Glass - Pneumofore Rotary Vane Technology
Click to watch
this video